0704 814 191 hello@renkelly.com Brisma Towers, Ongata Rongai
Mon – Sat, 8am – 6pm
Get a quote
Services

Concrete floor finishing, done properly.

Seven services from one specialist crew. We finish new slabs on pour day and restore or coat existing floors. We do not supply concrete, so our advice on your mix is independent.

Own machinesEngineer-ledWritten warranty
Walk-behind power trowel on a fresh concrete slab
Power floating by Renkelly

Power floating

We arrive on pour day with ride-on and walk-behind power floats. We float the slab once it reaches the right set, then trowel it to a smooth, tight finish. The result is one solid floor that takes forklift traffic, pallet racking and daily washing without dusting.

Where it’s used
Warehouses, godowns, factory floors, workshops, parking decks, house slabs
Key benefit
A flat, dense, hard-wearing surface finished while the concrete is still workable. There is no separate screed layer to crack or delaminate.
Typical turnaround
48 hours
Power troweling by Renkelly

Power troweling

Troweling follows floating, with steeper blade angles and higher speeds. Each pass compacts the top layer, giving a tighter surface that resists wear. We can leave a light broom texture on ramps and wet areas for grip.

Where it’s used
Industrial slabs, showrooms, commercial ground floors, garages
Key benefit
Closes the surface for a smooth, low-dust, easy-to-clean finish. We can burnish it to a sheen where you want one.
Typical turnaround
Same day as the pour
Screeding & levelling by Renkelly

Screeding & levelling

We set out levels, run screed rails and strike the concrete off to the right height and falls. On existing slabs we lay bonded screeds where we cannot power float the structural slab.

Where it’s used
New slabs, upper floors, existing slabs that need a level topping
Key benefit
Gets the floor level and to the right falls before finishing, so water drains where it should and racking sits true.
Typical turnaround
1 – 3 days
Industrial floor hardeners by Renkelly

Industrial floor hardeners

We broadcast a dry-shake hardener onto the fresh slab and power-float it in, so it becomes part of the surface. Older floors can be treated with liquid densifiers. Hardeners also come pigmented for coloured power float floors.

Where it’s used
Warehouses, cold rooms, loading bays, factories with steel-wheeled trolleys
Key benefit
Much higher abrasion resistance than plain concrete, less dusting and a longer floor life under heavy traffic.
Typical turnaround
Applied on pour day
Polished concrete by Renkelly

Polished concrete

We grind the cured slab with finer and finer diamonds, densify it and polish it to the sheen you choose, from satin to high gloss.

Where it’s used
Showrooms, offices, malls, restaurants, modern homes
Key benefit
A sealed, glossy, low-maintenance floor that reflects light, with no tiles to crack or grout to clean.
Typical turnaround
3 – 7 days
Epoxy flooring by Renkelly

Epoxy flooring

We prepare the surface by grinding or shot-blasting, repair defects, then apply primer and epoxy coats. A power-floated slab is the best base for epoxy because it is already flat and dense.

Where it’s used
Food and pharma plants, workshops, labs, hospital areas, car showrooms
Key benefit
A seamless, hygienic coating that resists chemicals, with optional anti-slip grit and line marking.
Typical turnaround
2 – 5 days plus cure
Floor repairs & resurfacing by Renkelly

Floor repairs & resurfacing

We rout and fill cracks, repair joints, patch spalled areas, grind high spots and resurface with a bonded topping or hardener. If a repair will not last and a new slab is the better spend, we will tell you.

Where it’s used
Cracked, dusting or worn floors in warehouses, factories, garages and homes
Key benefit
Brings a tired floor back into service without breaking it out.
Typical turnaround
1 – 5 days
Power float vs screed

One layer beats two

Switch between the two to compare.

Monolithic power-floated slab finishOne solid layer
  • Finished while fresh, so the surface is part of the slab
  • Flatter and denser, with far less dusting
  • No separate layer to crack, sound hollow or delaminate
  • One trade, one pour day and a lower total cost
Free site visit · No obligation

Tell us about your floor

Three quick steps. Your details open in WhatsApp, ready to send to our lead engineer.

  • Starting from Ksh 250 per sqm
  • A fixed written quote after a free site visit
  • Our own ride-on & walk-behind machines and trained crew
  • A workmanship warranty on every job
Renkelly crew in branded uniforms and helmetsReplies come from a lead engineer, not a call centre.

Step 1 of 3

What are we finishing?

Building Stronger Together

Pouring soon? Let’s plan your floor.

Send your area and location. A lead engineer replies within 30 minutes during working hours.

Chat with us
Call WhatsApp Quote