Concrete floor finishing, done properly.
Seven services from one specialist crew. We finish new slabs on pour day and restore or coat existing floors. We do not supply concrete, so our advice on your mix is independent.


Power floating
We arrive on pour day with ride-on and walk-behind power floats. We float the slab once it reaches the right set, then trowel it to a smooth, tight finish. The result is one solid floor that takes forklift traffic, pallet racking and daily washing without dusting.
- Where it’s used
- Warehouses, godowns, factory floors, workshops, parking decks, house slabs
- Key benefit
- A flat, dense, hard-wearing surface finished while the concrete is still workable. There is no separate screed layer to crack or delaminate.
- Typical turnaround
- 48 hours

Power troweling
Troweling follows floating, with steeper blade angles and higher speeds. Each pass compacts the top layer, giving a tighter surface that resists wear. We can leave a light broom texture on ramps and wet areas for grip.
- Where it’s used
- Industrial slabs, showrooms, commercial ground floors, garages
- Key benefit
- Closes the surface for a smooth, low-dust, easy-to-clean finish. We can burnish it to a sheen where you want one.
- Typical turnaround
- Same day as the pour

Screeding & levelling
We set out levels, run screed rails and strike the concrete off to the right height and falls. On existing slabs we lay bonded screeds where we cannot power float the structural slab.
- Where it’s used
- New slabs, upper floors, existing slabs that need a level topping
- Key benefit
- Gets the floor level and to the right falls before finishing, so water drains where it should and racking sits true.
- Typical turnaround
- 1 – 3 days

Industrial floor hardeners
We broadcast a dry-shake hardener onto the fresh slab and power-float it in, so it becomes part of the surface. Older floors can be treated with liquid densifiers. Hardeners also come pigmented for coloured power float floors.
- Where it’s used
- Warehouses, cold rooms, loading bays, factories with steel-wheeled trolleys
- Key benefit
- Much higher abrasion resistance than plain concrete, less dusting and a longer floor life under heavy traffic.
- Typical turnaround
- Applied on pour day

Polished concrete
We grind the cured slab with finer and finer diamonds, densify it and polish it to the sheen you choose, from satin to high gloss.
- Where it’s used
- Showrooms, offices, malls, restaurants, modern homes
- Key benefit
- A sealed, glossy, low-maintenance floor that reflects light, with no tiles to crack or grout to clean.
- Typical turnaround
- 3 – 7 days

Epoxy flooring
We prepare the surface by grinding or shot-blasting, repair defects, then apply primer and epoxy coats. A power-floated slab is the best base for epoxy because it is already flat and dense.
- Where it’s used
- Food and pharma plants, workshops, labs, hospital areas, car showrooms
- Key benefit
- A seamless, hygienic coating that resists chemicals, with optional anti-slip grit and line marking.
- Typical turnaround
- 2 – 5 days plus cure

Floor repairs & resurfacing
We rout and fill cracks, repair joints, patch spalled areas, grind high spots and resurface with a bonded topping or hardener. If a repair will not last and a new slab is the better spend, we will tell you.
- Where it’s used
- Cracked, dusting or worn floors in warehouses, factories, garages and homes
- Key benefit
- Brings a tired floor back into service without breaking it out.
- Typical turnaround
- 1 – 5 days
One layer beats two
Switch between the two to compare.
One solid layer- Finished while fresh, so the surface is part of the slab
- Flatter and denser, with far less dusting
- No separate layer to crack, sound hollow or delaminate
- One trade, one pour day and a lower total cost
Two layers- An extra layer applied days or weeks later
- A weaker bond that can sound hollow and break up under forklifts
- More material, more labour and more time
- Often needs a hardener or coating on top anyway
Tell us about your floor
Three quick steps. Your details open in WhatsApp, ready to send to our lead engineer.
- Starting from Ksh 250 per sqm
- A fixed written quote after a free site visit
- Our own ride-on & walk-behind machines and trained crew
- A workmanship warranty on every job
Replies come from a lead engineer, not a call centre.